--
SHARES
  

Photos: Rocky Mountain Bicycles.

The Slayer has been Rocky Mountain’s enduro, all-mountain, freeride, bike park weapon for ages — almost 20 years, in fact. Piloted by enduro athletes Remi Gauvin and Jesse Melamed or freeriders Carson Storch and Thomas Vanderham, the Slayer’s intent is easily noticeable.

For 2020, Rocky Mountain has beefed up the Slayer more than ever. Rocky says that as downhill bikes are segmenting even further into a dedicated race category, riders that want a dedicated bike park rig or a bike for the most technical enduros are looking for something different. The 2020 Slayer intends to be a beefy rig for gnarly downhills, but with new kinematics to make it reasonable to pedal up to the top of the mountain.

Rocky Mountain tuned the anti-squat on the Slayer’s new suspension for improved small bump compliance and reduced pedal kickback.

The frame design is markedly different from the previous Slayer, with its jet-like lines. The new frame takes on the lines and look of an Altitude or Instinct, but with a reinforced front triangle for stiffness and durability. The carbon frames are also paired with an aluminum rear end. All sizes will fit a water bottle in the front triangle even with a piggy-back shock.

Most notably, the new Slayer is available in either 29- or 27.5-inch wheels, a first for the model which has always come in a smaller wheel size.

The smaller-wheeled Slayer has a 180mm fork with a 37mm offset and 180mm of rear suspension travel. It can fit a maximum 36-tooth chainring and is available in sizes S-XL.

The big-wheeled Slayer comes with a 170mm fork with a 42-44mm offset and 170mm rear suspension travel. The 29er will fit a maximum 34-tooth chainring. Both wheel sizes can accommodate up to a 2.6-inch-wide tire in the rear.

Geometry differs slightly between the two wheel sizes, but there are big changes from the previous version.

Geometry for the 29-inch Slayer.

In the most slack position of the Ride-4 adjustable geometry, the Slayer is about a degree slacker than the previous and the seat tube angle is about two-degrees steeper.

Geometry for the 27.5-inch Slayer.

Depending on the geometry position again, the reach is about 20mm longer.

The Ride-4 adjustably geometry is still changeable with a hex key. The suspension is tuned differently across all sizes.

Remi Gauvin whipping the new Slayer.

If the travel and geometry numbers haven’t reinforced the idea that the Slayer is made for the biggest lines on the mountain, then the weights will.

For the 29er, the carbon frame and shock weighs 9.26lbs. The top-end Slayer Carbon 90 weighs in at 33.8lbs, and a Slayer Alloy 50 weighs 37.1lbs, in size medium.

For the medium 27.5-inch version, it loses a little weight and a frame and shock weighs 8.8lbs, the Slayer Carbon 90 weighs 33.5lbs., and the Alloy 50 weighs 36.1lbs.

Carson Storch putting the new Slayer to work in Utah.

Top end Carbon 90 builds include Shimano XTR Trail 4-piston brakes with 203mm rotors, an XTR drivetrain, Race Face ARC 30 rims with DT Swiss hubs, and Maxxis tires with Double Down casing.

An alloy 30 base model has a RockShox Yari RC, a RockShox Super Deluxe Coil Select rear shock, a SRAM SX Eagle drivetrain, and WTB wheels with Maxxis Double Down casing tires.

Considering that a lot of brands use a single-ply tire on their stock builds to bring the weight down, the double-ply tires no doubt add to the Slayer’s stock weight.

For more information visit the Rocky Mountain website.

--
SHARES
  
# Comments

  • Downhill Mike

    I own older version Slayer and it’s a great very capable bike. Not the best rig for climbing but I have climbed close to 2000m on it during some rides and it wasn’t too bad. It descents almost like a downhill bike.

Leave a Reply

You must be logged in to post a comment.


Trending
153 SHARES | 11 COMMENTS